Made of wear resistant, hardened steel, with a sturdy wall thickness for a long service life and a minimum of wear and tear. This nozzle is used to penetrate blockages and make an initial opening in a blocked line. The 30 degrees jet angle provideds positive thrust and a good cleaning of the pipe wall. All nozzles from 03.038 and above are fitted with ceramic insert jets as standard, this provides a service life twice as long as any comparable drilled nozzle.
|
 |
Made of wear resistant hardened steel. The grenade bomb has been designed with jets set at both at angles of 10 & 30 degrees and a heavy weight for its size. These factors allow the nozzle to travel in the lower half of the pipe. The Nozzle provides a strong traction and effective removal of loose rubble, sand, stone and soft deposits. This Nozzle can also be used for pre-cleaning before the use of an ENZ Chain Flail head or Rootcutter.
|
|
Designed to penetrate the toughest blockages the Enz pointed nozzle directs 30% of your jetters flow forward 15 degrees through its hardened tip to break up and open the blockage. The remainder is exausted at a 20 degree angle to provide positive thrust and penetrating power. Ideal for roots, silt, heavily blocked pipes and frozen pipes.
|
|
A specialist nozzle for cleaningbox culverts, flat pipes and channels. Its rounded corners enable it to glide up the pipe with ease. This tool is particularly suited to removing sand, silt and rubble.
|
|
A heavy nozzle for cleaning the bottom of pipes or channels between 200mm to 3m in diameter. Good for the removal of silt, gravel, sand and rubble.
|
|
This rotating nozzle has 4 jets set at 80 degrees for cleaning the pipe wall, and 3 rear mounted thrust jets to provide forward motion. This nozzle is used to clean pipes and ducts and is especially good at cleaning out pipe joints and junctions.
|
|
This roatating nozzle is fitted with 4 retroacting cutting jets set at an angle of 45 degrees to provide both thrust and maximum pipe wall cleaning. This nozzle can also be fitted with a foward nozzle or thruster nozzle's if required. It is ideal for fat, silt or cleaning before CCTV surveys.
|
|
The HRV nozzels have 4 semi radial rotating nozzles facing foward firing at an angle of 45 degrees and a front forward firing jet as well as rear mounted thruster nozzles. This nozzle has a corkscrew like action in the pipe, breaking up the blockage with the front nozzles, while the rotating jet scours the pipe wall discharging the residue. The rear thrusters provide foward motion as well as simultaneously flushing the waste.
|
|
This roating nozzle is fitted with 2 spinning jets set at 90 degrees and 2 semi radial rotating jets set at 45 degrees. This combination allows, positive foward thrust and flushing of the debris as well as cleaning of the pipe wall and pipe joints.
|
|
The KBVR nozzle has 2 semi radial jets directed forward at an angle of 45 degrees and 2 nozzles set at 90 degrees to the pipe wall. It is also fitted with 3 rear thruster nozzles to provide positive forward movement in th pipe.
|
|
This controlled rotation nozzle has been built with a clever oil free braking system and can be used with either fresh or recycled water. The bulldog is almost maintenance free and is very easily handled, offering the user a very efficient cleaning system. The slow rotation speed results in a longer jet time on targets and is devastating to even the toughest pipeline deposits.
|
|
The Rotopuls nozzles were conceived to remove medium to hard deposits in pipes of plastic, steel or concrete. Important: Rotopuls nozzle develop strong hydraulic impacts and vibrations. This can possibly cause damage in some types of pipe (e.g. earthenware pipes, thin-walled plastic pipes or badly bedded PVC pipes)
|
|
This attachment is a highly efficient tool for the cleaning of large channels of either round or oviform pipe, through the combination of thrusting jets and the propeller nozzle jets. This unit is able to be used with recycled water.
|
|
The ENZ gliding nozzles are designed to give a small volume of jet the ability to clean pipe walls up to 400mm in diameter. As a result they work very close to the pipe wall and use very little water!
|
|
These maximum pressure rotating nozzles are most efficient in cleaning the inside wall of pipes with a pressure up to 1000 bar. They are appropriate in removing harder deposits from pipe walls, heat exchangers, chemical and atomic plants and for general industrial pipe cleaning.
Available in RGS, HRH, HRV, KBRV configurations with varying diameters from 1/8 " to 1/4" and from M7 to M24..
|
|
Used in conjunction with a lance for industrial cleaning purposes such as heat exchanges, boilers and in small diameter completely blocked pipes. This nozzle uses an ingenious array of jets to remove the toughest deposits
|
|
The Enz Chain Flail head has many uses and is simple to maintain and handle. Several different pipe diameters can be cleaned with the same tool and it can be fitted with various size chains, skids and cutters. Used to remove, tree roots, calcarious deposits and concrete residue.
|
|
The impact Drilling Cutter is capable of removing the most stubborn deposits like concrete, injections cement and calarious layers etc. Fitted with CArbide -tipped teeth and able to clean pipes between 200mm to 600mm in diameter. The unit is capable of speeds of between 670-3000rpm. and is capable of exerting an impact force of up to 8T.
|
|
Enz Ceramic inserts offer the user a longer service life compared with inserts made of hardened steel and deliver a compact and aggresive stream of water against the pipe wall. These inserts are available in multiple diameters and thread sizes M4 to M10 as well as 1/4" B.S.P.
|
|
Provided for the use with nozzles for larger channel cleaning and for operating cutters. Rustproof with smooth operation and cause no reduction on water flow rate.
|
|
These cutters are equipped with tungsten carbide tipped teeth and are able to remove various kinds of deposits such as calcarious layers, concrete, concrete sludge, roots and wood.
|
|
